gday the plan is to put BA xr6 motor into EA falcon i no i gotta cut out the bonnet and stuff like that but i just need a site or anything where i can get parts and the actual BA xr6 motor.
cheers.
hey im new can some one help?
6 posts
• Page 1 of 1
hey im new can some one help?
by EaJonzy » December 12th, 2008, 4:11 pm
1990 EA Falcon S Pack T5.
4.0 EF Xr i6 - 3" custom exhaust - Hurricane Extractors
2009 YZ 250
4.0 EF Xr i6 - 3" custom exhaust - Hurricane Extractors
2009 YZ 250
-
EaJonzy - Idling
- Posts: 38
- Joined: December 12th, 2008, 3:53 pm
- Location: Tweed Heads
- Has Liked: 0 time
- Been Liked: 0 time
1990 Ford S Pack
Re: hey im new can some one help?
by Gozza » December 12th, 2008, 4:14 pm
Noone can help you - Ever!!!
Its a stack of f*ck shit, on top of itself niggaaaaaa
-
Gozza - Hitting N2O
- Posts: 3609
- Joined: August 10th, 2007, 11:31 am
- Location: Brisbane
- Has Liked: 1 time
- Been Liked: 3 times
1992 Ford Falcon
Re: hey im new can some one help?
by holmsy » December 12th, 2008, 4:15 pm
wreckers are probably your best bet.
or maby ebay.
its a fair job. to my knowledge there is only 1 or 2 on here that are running properly.
or maby ebay.
its a fair job. to my knowledge there is only 1 or 2 on here that are running properly.
Project: SLOXR8: 1994 EF XR8, mech shift kit, 3500 histall, Lokka, 36lb injectors, AU 185 motor, Cranecam 444225, crane roller rockers, crow valve springs, Pacies, 3" exhaust, hiflo cats. twin 044's, vortech v2,microtech tuned by daltons (290.3rwkw @11psi) at DALTONS
-
holmsy - Shooting Flames
- Posts: 6473
- Joined: August 2nd, 2007, 11:07 pm
- Location: Geelong
- Has Liked: 182 times
- Been Liked: 154 times
1994 Ford XR8
Re: hey im new can some one help?
by Malakai » December 12th, 2008, 4:18 pm
To do it with the least fuss you need a complete motor and wiring/engine loom from a BA. You need to install it all into the EA and make some wiring changes to get everything to work.
If you have limited knowledge of BA's then it's best to get an experienced workshop to do it for you.
If you have limited knowledge of BA's then it's best to get an experienced workshop to do it for you.
FG G6E Turbo MkII - Nizpro Stage 3 - 364 rwkW - 11.63 sec @ 118 mp/h | I like the dark, I love the dark, but I hate nature. 
-
Malakai - Double Clutching
- Posts: 5251
- Joined: July 21st, 2007, 1:23 pm
- Location: Brisbane
- Has Liked: 0 time
- Been Liked: 32 times
Re: hey im new can some one help?
by pommyebxr6 » December 12th, 2008, 10:07 pm
id say buy a rear end ba which is smashed so u have everything u need as u would have the complete car....do the conversion....strip whats parts are good on the ba and sell them.
but thats me and im a pommy what do i know
but thats me and im a pommy what do i know
- pommyebxr6
- Idling
- Posts: 54
- Joined: December 1st, 2008, 8:53 pm
- Has Liked: 0 time
- Been Liked: 0 time
Re: hey im new can some one help?
by Bipolar » December 13th, 2008, 12:07 am
All the above replies are accurate. I'd do a buttload of research before you even think about beginning a project like this.
RBKILA wrote:yes im sure 99% of the hate is just jealousy from morons.
the same sort of people you see at bathurst, wearing all the hrt gear and then you see them get into a camry in the car park lol
-
Bipolar - Moderator
- Posts: 4493
- Joined: July 24th, 2007, 6:49 pm
- Has Liked: 741 times
- Been Liked: 225 times
1997 Ford Falcon
6 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users