Boosted Falcon

Posted: **January 24th, 2008, 10:43 am**

who knows where 2 get clear repeaters from 4 eb?

Posted: **January 24th, 2008, 10:44 am**

look for any VX at a shopping centre

Posted: **January 24th, 2008, 10:46 am**

ebay, Ford Service, etc.

I got mine from Holden

Posted: **January 24th, 2008, 10:48 am**

do they fit from VX 2 eb no worries?

Posted: **January 24th, 2008, 10:49 am**

close enough to no worries. Rollin had these on his red EB XR6 from memory

Posted: **January 24th, 2008, 11:22 am**

thanks mate

Posted: **January 24th, 2008, 11:34 am**

AUIII also fit, think i got my old ones from bursons. put them on backwards and do a little chop chop of the grey strip. 5min max to install. dont forget orange globes for the clear repeater!!

Posted: **January 24th, 2008, 11:50 am**

EDFalcon wrote:AUIII also fit, think i got my old ones from bursons. put them on backwards and do a little chop chop of the grey strip. 5min max to install. dont forget orange globes for the clear repeater!!

yeh i heard that. duz any1 no if u need2 chop chop 2 fit VX 1's?

Posted: **January 24th, 2008, 12:01 pm**

blackebII wrote:yeh i heard that. duz any1 no if u need2 chop chop 2 fit VX 1's?

Pardon me, are you requesting advice on modifying your side repeaters, or are you trying to sell backyard tobacco from the western suburbs on here?

Posted: **January 24th, 2008, 12:04 pm**

hahaha very good i pay that
seriously though do u need 2 modify the gaurd 2 fit vx 1's?

Posted: **January 24th, 2008, 12:12 pm**

IIRC not the guard, just the repeater itself. I had to trim my std EB plugs to fit into my WK repeaters. Also I glued my repeaters to the guard (well, the mould on the guard), not sure if this is the case with VX repeaters.

Posted: **January 24th, 2008, 12:51 pm**

pretty sure they have a similare setup to the AUIII ones. dont have to chop the mould by the way i should have said you can either open up the guard with a sharp knife or shave back the repeater also with a sharp knife. either one works.

Posted: **January 25th, 2008, 7:13 am**

ok thanks guys

Posted: **January 25th, 2008, 7:20 am**

Come to think of it, EFFalcon posted up a tech thread on how to fit AU repeaters.

Here it is

viewtopic.php?f=35&t=1878

Posted: **January 25th, 2008, 7:23 am**

Would you like to know how to use VHT on your dash as well????

Posted: **January 25th, 2008, 7:30 am**

VHT? wat?

Posted: **January 26th, 2008, 11:12 am**

VHT is paint dude....and no, you do not want to paint your dash!

VX ones fit ok, slightly loose though, so you might need to put a little silastic or something on them to keep them in place.

You can buy the proper plugs and connectors, which come with about 15cm of wiring, so you can solder the wires to your original harness and have connectors and plugs that fit properly.

Posted: **January 26th, 2008, 5:19 pm**

Rollin wrote:VHT is paint dude....and no, you do not want to paint your dash!

VX ones fit ok, slightly loose though, so you might need to put a little silastic or something on them to keep them in place.

You can buy the proper plugs and connectors, which come with about 15cm of wiring, so you can solder the wires to your original harness and have connectors and plugs that fit properly.

thanks mate

Posted: **February 11th, 2008, 4:47 pm**

ok so iv got some VY and some VX clear side repeaters now,
the VY dont clip in they r 2 small,
the VX r close but the securin clips on them r broken so they fall out,
so either way im gona have 2 selastic or glue them in, is that a bad idea?

VX

VY

wats ur ideas?

Posted: **February 11th, 2008, 4:58 pm**

Glue

can always apply heat & melt off, or use fishing wire & "saw" off

Posted: **February 11th, 2008, 5:00 pm**

chuck in new globes, selastic them in, job done

Posted: **February 11th, 2008, 5:03 pm**

i dummy fitted wk indicators on my NC lane, they looked mad. should try a set of those. I ended up putting AU3 indicators, glued the bastards on

Posted: **February 11th, 2008, 5:09 pm**

so is it glue or selastic?
VX orVY?

Posted: **February 11th, 2008, 5:17 pm**

blackebII wrote:so is it glue or selastic?
VX orVY?

is your car mate, why not do what you want

Posted: **February 11th, 2008, 5:28 pm**

bubble gum

Posted: **February 11th, 2008, 5:28 pm**

blu tak

Posted: **February 11th, 2008, 5:29 pm**

yeh jus gettin some opinions

Posted: **February 11th, 2008, 5:44 pm**

Damo wrote:bubble gum

Lol, thats how one of mine are at the moment :cry:

was washing my car at carwash and i bumped it to hard and snapped the leg of, needed a quick fix and i had some gum in my mouth...

Posted: **February 11th, 2008, 7:22 pm**

^^^ That's so Bill & Ted :lol:

Posted: **February 12th, 2008, 9:27 am**

Look for some AUIII they go on with hardly any troubles and wont need to glue them on.

Posted: **February 12th, 2008, 11:02 am**

Commando wrote:^^^ That's so Bill & Ted

Dave wins the award for obscure movie reference of the week.

I will say, don't bother with BA repeaters. I bought some, they look rubbish. Personally, I would go for the VY ones, the squarer shape suits the style of the car better.

Posted: **February 12th, 2008, 11:20 am**

(they used gum to fix the munted antenna on their time travelling phone booth)

Posted: **February 13th, 2008, 8:29 am**

spope wrote:
Commando wrote:^^^ That's so Bill & Ted

Dave wins the award for obscure movie reference of the week.

I will say, don't bother with BA repeaters. I bought some, they look rubbish. Personally, I would go for the VY ones, the squarer shape suits the style of the car better.

thanks 4 the opinion mate

Posted: **February 13th, 2008, 9:50 pm**

Commando wrote:(they used gum to fix the munted antenna on their time travelling phone booth)

lol
i haven't seen that movie in years!

Boosted Falcon

clear repeaters

clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters

Re: clear repeaters