Body kit for AU series 3?
7 posts
• Page 1 of 1
Body kit for AU series 3?
by jaixion » June 12th, 2012, 1:20 pm
I have a series 3 AU and I'm wanting to put a kit on it. I have 19" mags at the moment so the car sits a little too high for my liking. Wondering which body kit will fit an AU, and where can I get it?
- jaixion
- Cranking Over
- Posts: 1
- Joined: June 12th, 2012, 1:08 pm
- Has Liked: 0 time
- Been Liked: 0 time
2000 Ford AU series 3 Sedan
Re: Body kit for AU series 3?
by justa6 » June 12th, 2012, 1:28 pm
Fibresports
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
-
justa6 - Full Boost
- Posts: 2986
- Joined: February 24th, 2008, 2:55 pm
- Has Liked: 88 times
- Been Liked: 525 times
1999 Ford xr6 ute
Re: Body kit for AU series 3?
by Dansedgli » June 12th, 2012, 2:31 pm
If the car is too high you should lower it more, not stick more plastic on it.
Pm wildeb.
Pm wildeb.
-
Dansedgli - Melting Pistons
- Posts: 9734
- Joined: July 13th, 2007, 11:35 am
- Location: Melbourne
- Has Liked: 75 times
- Been Liked: 542 times
2001 Ford Falcon Ute
Re: Body kit for AU series 3?
by Nikk O'lass » June 12th, 2012, 4:49 pm
Au's look better clean...too many T3 tryhards..\
Dump it! Or, if you must get a kit, the ticky kit look good enough, or a "havoc" kit.
Dump it! Or, if you must get a kit, the ticky kit look good enough, or a "havoc" kit.
.T..I..C..K..F..O..R..D
\≡≡T≡≡/
\≡≡T≡≡/
-
Nikk O'lass - Full Boost
- Posts: 2203
- Joined: September 9th, 2007, 8:14 pm
- Location: Tamworth
- Has Liked: 99 times
- Been Liked: 125 times
1998 Ford XR6
Re: Body kit for AU series 3?
by justa6 » June 12th, 2012, 6:45 pm
Dansedgli wrote:If the car is too high you should lower it more, not stick more plastic on it.
Pm wildeb.
yeah that is pretty good advice right there. if it is high and gay now, it will still be high and gay after. drop it.
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
-
justa6 - Full Boost
- Posts: 2986
- Joined: February 24th, 2008, 2:55 pm
- Has Liked: 88 times
- Been Liked: 525 times
1999 Ford xr6 ute
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users