a/c in turboed au

This is a general discussion forum, open to all participants
Post a reply

a/c in turboed au

Postby AU DR » March 16th, 2015, 1:47 pm

Gday again
Any tips how to fit the condenser between the radiator and intercooler and does the standard radiator handle the turbo
] Cheers Dave
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby AU DR » March 18th, 2015, 8:26 pm

What's going on out surly someone has some advice
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby OED666 » March 18th, 2015, 11:47 pm

Depends on how big your intercooler is for any issues with the radiator.

I'm deciding on either a 480x300 or 600x300. I don't see the condenser being an issue, however the receiver/drier will need to be relocated, and also new A/C lines made up.


Sent from my iPhone using Tapatalk
Image

Sundeep wrote:even though Falcon manuals are rough as guts. I just like smashing and skating through gears.
User avatar
OED666
Hitting N2O
 
Posts: 3792
Joined: August 3rd, 2007, 8:20 am
Location: At your mum's house, and she loves it!
Has Liked: 194 times
Been Liked: 121 times

1994 Ford Falcon
Top

Re: a/c in turboed au

Postby AU DR » March 19th, 2015, 3:26 am

I have a 600 x 300 as far forward as can go on AU with front support and the pipes on the Condensor rap around in between causing the problem may have try and cut them and run them from the end ???
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby justa6 » March 19th, 2015, 5:30 am

I had to take a little off the webbing of the bar at the front, just on the outside edges of the cooler. Then the cooler could move forward as far as possible.

I've had the standard radiator for years.
Image
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
User avatar
justa6
Full Boost
 
Posts: 2986
Joined: February 24th, 2008, 2:55 pm
Has Liked: 88 times
Been Liked: 525 times

1999 Ford xr6 ute
Top

Re: a/c in turboed au

Postby AU DR » March 19th, 2015, 12:50 pm

Thanks for that did your engineer have anything to say about that
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby justa6 » March 19th, 2015, 5:00 pm

If you do it neat, it looks fine.

Yeah my engineer loves my Ute.
Image
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
User avatar
justa6
Full Boost
 
Posts: 2986
Joined: February 24th, 2008, 2:55 pm
Has Liked: 88 times
Been Liked: 525 times

1999 Ford xr6 ute
Top

Re: a/c in turboed au

Postby AU DR » March 19th, 2015, 5:40 pm

All good then hope mine has the same affect and thanks for help
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby Jayedxr6 » March 19th, 2015, 9:52 pm

Marty you being the engineer
Xh falcon turbo. 420rwhp 16 psi.
User avatar
Jayedxr6
Breaking Traction
 
Posts: 1954
Joined: November 26th, 2011, 6:40 pm
Has Liked: 179 times
Been Liked: 149 times

1994 Ford ED Falcon XR6
Top

Re: a/c in turboed au

Postby AU DR » March 20th, 2015, 2:12 am

R so that's how it works is that love for sale or just self gratification
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby justa6 » March 20th, 2015, 12:23 pm

Depends, have you got big tits and tight arse Haha.

Na Mine's not engineered mate. Should do it, just haven't been bothered for how much I drive it on the road.
Image
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
User avatar
justa6
Full Boost
 
Posts: 2986
Joined: February 24th, 2008, 2:55 pm
Has Liked: 88 times
Been Liked: 525 times

1999 Ford xr6 ute
Top

Re: a/c in turboed au

Postby AU DR » March 20th, 2015, 1:03 pm

Might get someone with big tits and a tight arse to take it to the engineer
AU DR
Idling
 
Posts: 29
Joined: August 1st, 2014, 5:26 am
Has Liked: 1 time
Been Liked: 0 time
Top

Re: a/c in turboed au

Postby justa6 » March 20th, 2015, 8:36 pm

I like your thinking.
Image
manley rods, sps pistons, billet surecam, gt4202r 1.15, 6boost manifold, 60mm gate, 4" exhaust, nizpro plenum, 80mm throttle body, bosch 2000cc injectors, 2x044, -8 fuel line, standard fuel rail modified -8 in-out. c4 box 3000 stall, standard diff with 31 spline axles, full spool.
477rwkw 24psi. 9.80 @ 145mph
User avatar
justa6
Full Boost
 
Posts: 2986
Joined: February 24th, 2008, 2:55 pm
Has Liked: 88 times
Been Liked: 525 times

1999 Ford xr6 ute
Top
Post a reply

Return to General Discussion

Who is online

Users browsing this forum: No registered users

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group