EB-3022 EB series 1 . 91 FAIRMONT GHIA 5 litre R.I.P,

[SnyperEB]

found this nice pic of a ed xr8 sprint with big ass momo rims.

Lenso not Momo.

[icachn]

[icachn]

still undecided on which rear bar to go with.was thinking maybe a eb gt one but dont know if it would look good with what i have atm on the car.also prefer to deal with someone in melb rather than paying for freight interstate.

[icachn]

Vinyl wrapped the rear window section black similar to EA SVOs, i reckon it looks alright.

[krisisdog]

Do the B pillar

[icachn]

Do the B pillar

yeh was thinking of doing the door pillar also.

[icachn]

b pillar done in black vinyl.

[EFFalcon]

Black b pillar suits good.

[freerider]

where did you get the vinyl from? and is just a stick on sorta thing?

[icachn]

where did you get the vinyl from? and is just a stick on sorta thing?

i got it from kmart ,its meant for book covering but u can use any sticker/vinyl from a sticker making place.its a cheaper non permanent alternative to paint.

[icachn]

new jvc headunit with bluetooth and soundstream 4 " front speakers going in soon.

[icachn]

.

[icachn]

[icachn]

front 4" soundstream speakers in, as well as new jvc headunit with bluetooth ,front/rear usb, and iphone/ipod connectivity.

[icachn]

[Dumpsta]

Looks good. Leave the C pillar white imo, but they look so much cleaner with the b-pillar black, I did mine a couple years ago for the same result.

[icachn]

[icachn]

old and new au side repeaters. got them from online performance autos in Hallam for $25 a pair.

[icachn]

how good does this xr au ute look with a black bonnet and bulge.mite do the same with my eb.

[icachn]

does any body know how the ba headlight conversion is done on eb headlights. i believe u must buy the ba headlights to do this?? any info please...

[icachn]

wana do something similar to this custom bonnet on this ba . fg bulge with cutouts and gt black sticker.

[icachn]

picked up an eb gt rear bar today for my eb for only $50, but had to go to Shepparton to get it. will be dropping it off at panel shop soon to be painted and fitted.

[wombi90]

Car looked good when you picked it up didn't think it was going to fit in there haha

[icachn]

Car looked good when you picked it up didn't think it was going to fit in there haha

yeh lucky we just made it fit in, i actually did 400 kms all up and went thru one full tank of gas ( $ 30 ) .it was a good day for a drive, haven been up that way for a while now.

[icachn]

.

[braad]

.

i agree



ask benj about the headlight mod, he has a thread on the wagon on here
http://www.boostedfalcon.net/viewtopic.php?f=3&t=9453

[icachn]

.

yeh it doesnt actually say how the ba headlight conversion is done.. anyone know??

[SnipeZ]

Found this in my messages. Might be of some help

Gidday

You need a pair of BA headlights.

Remove the clear lense (PITA) and the extract the reflector.

Using an empty EB headlight frame, slide the BA reflector in. Note where it does not fit, and trim the top and the bottom of the low beam light.

When you can get the low beam in most of the way, you need to fabricate mount points of the EB light adjusters, to the back of the BA reflector.

Paint the inside of the EB frame black, and the non reflective areas of the reflector black.





Assemble with care.

For globes, the EB low beam are a direct fit, but you will need the BA high beam ones. Mod wiring if needed.

BenJ

Cheers

[BenJ]

Oh, yeah, meant to reply to this the other day and got distracted.

My Fordmods thread has the above info.

That is about all there is to it really.

Use long screws and springs out of a bic click pen for the adjustable mounts, bottom left and right of the lense. Use the centre top EB pivot point as the fixed location.

Good luck.

Cheers
BenJ

[icachn]

dropped car off at panel shop this morning to get eb gt rear bar painted white with a black bottom section . should look good wen finished.next on the list will be the fg bonnet bulge i think.just got to save a bit more for that.

[icachn]

rear bar painted and fitted, pretty happy with the result.

[EFFalcon]

Looks pretty good.
I'd probably do something with the door moulds, either fully colour code, or maybe black out the gray line to match the rest of the blackouts.

see if you can think of a way to match up where the rear bar meets the wheel arch, since it looks like its pushed out due to normally having the flares fitted.

otherwise, top job!

[icachn]

Looks pretty good.
I'd probably do something with the door moulds, either fully colour code, or maybe black out the gray line to match the rest of the blackouts.

see if you can think of a way to match up where the rear bar meets the wheel arch, since it looks like its pushed out due to normally having the flares fitted.

otherwise, top job!

yeh probably will do the door moulds white to match the bodykit.

[sexyr6]

just remove the moulds all together, I was amazed what a difference it made when I removed mine.

[SnipeZ]

Don't remove them. Just paint the whole mould the same color


Cheers

[SnipeZ]

Saw this tonight on burwood hwy

Looked sweet as! Pictures don't do it justice


Cheers

[icachn]

[LUXO_8]

removing the moulds makes it look like they fell off, dont do it..

looks awesome now with the GT rear bar.. good work

[icachn]

[icachn]