t1MMy's XR6

Post by **Sunboost** » May 5th, 2009, 9:53 pm

What did you do? Flick the key back and roll to the side of the road? I'm guessing the gauge dropped and then the light came on?

What motor has it got lol? A Boss 260/290?

t1MMy · Post by **t1MMy** » May 5th, 2009, 10:01 pm

Yup, flicked the key off straight away, rolled till it came to a stop. Called Mr.CVE and asked for his advice, listened to it, got the car towed home, taking it to the workshop tomorrow for a fix hopefuly.

Nah no Boss motor for me.

Might have to get some lose change lying around and buy a BF turbo.....it's easier isn't it?..

Post by **EFFalcon** » May 6th, 2009, 9:38 am

shit news Timmy :/

t1MMy · Post by **t1MMy** » May 6th, 2009, 2:01 pm

Just got back from dropping the car off at the shop. Luck I have RACV total care free tows anywhere, anytime and option of a hire car. I would of had Mr.CVE look at it for me but after seeing his garage last night it's probably the last thing he needs with all those cars in there.
I'm hoping it's not going to cost an arm and a leg, I'm starting to run out of them

watch this space....

Steady · Post by **Steady** » May 6th, 2009, 2:13 pm

I got $20 on aux shaft.

Mr. CVE · Post by **Mr. CVE** » May 6th, 2009, 4:38 pm

Steady wrote:I got $20 on aux shaft.

I'll see your $20 and raise you $10 for seized oil pump!! which broke the rest of it !!

t1MMy · Post by **t1MMy** » May 6th, 2009, 5:01 pm

I hope you're wrong Paul, only problem is that you know better so you're probably right

SnyperEB · Post by **SnyperEB** » May 6th, 2009, 5:32 pm

t1MMy wrote:Might have to get some lose change lying around and buy a BF turbo.....it's easier isn't it?..

Thats what they do when it gets to hard for them. Its easier but you join the 500,000 of them and your car get lost in the crowd. Hope its an easy fix Timmy.

Dansedgli · Post by **Dansedgli** » May 6th, 2009, 5:42 pm

Because E series are so rare?

SnyperEB · Post by **SnyperEB** » May 6th, 2009, 5:47 pm

No becasue there is just so many BA's out there once you seen one you seen em all.

Compared to the standard shiz box e-series out there cars like timmy's turns heads at meets and cruises. BA's dont......

I myself personally just look at the BA at a cruise and think to myself oh yeah nice aftermarket 20's and walk off. However Timmy's car people would stop and actually look and the bodywork and the shiny new paint job and admire it the time and effort.

Thats my rant.

Parfrey · Post by **Parfrey** » May 6th, 2009, 6:11 pm

i was thinking aux shaft too...

e series are ok, but b series are waay better. Sure a modified eseries might turn a few more heads, but a ba would be better to drive/more reliable/easier to get power out of etc.

SnyperEB · Post by **SnyperEB** » May 6th, 2009, 6:18 pm

Ba is an easy way out of actually putting time and effort into a car.

shane-ed · Post by **shane-ed** » May 6th, 2009, 6:33 pm

selling wheels yes?
have u put them up for sale yet? how much are u asking?
thanks

t1MMy · Post by **t1MMy** » May 6th, 2009, 6:34 pm

shane-ed wrote:selling wheels yes?
have u put them up for sale yet? how much are u asking?
thanks

Sorry mate, you're about 3 months too late.

Post by **EFFalcon** » May 6th, 2009, 7:06 pm

SnyperEB wrote:Ba is an easy way out of actually putting time and effort into a car.

i wouldn't go that far

if you don't want it to be 'just another BA'
then you have to put some time/effort into it

but.. this is about Timmy's car, so BA's conversation is offtopic

SnyperEB · Post by **SnyperEB** » May 6th, 2009, 7:09 pm

EFFalcon wrote:
SnyperEB wrote:Ba is an easy way out of actually putting time and effort into a car.
i wouldn't go that far
if you don't want it to be 'just another BA'
then you have to put some time/effort into it

Alot of people dont....
Anyways back on topic. Hope you sort the problem out Timmy.

Post by **EFFalcon** » May 6th, 2009, 7:12 pm

SnyperEB wrote: Alot of people dont....

A lot of people drive dead stock cars too.
BA T's with 300rwkw > Stock Car

Post by **Sunboost** » May 6th, 2009, 7:19 pm

viewtopic.php?f=2&t=9445" onclick="window.open(this.href);return false;

bentls · Post by **bentls** » May 6th, 2009, 7:46 pm

oops sorry delete this didnt see sunnys thread

t1MMy · Post by **t1MMy** » May 7th, 2009, 2:13 pm

*UPDATE*

There is no good news I'm afraid. It was the aux shaft, all the teeth on the gear were just about all stripped off which in turn fvkd the other gears causing some damage.

Put another aux shaft in to see what that go is and it made oil pressure but was making a hell of a noise becasue it fooked the other gears. So oil pump is fine but sounds like all the gears that run off it are in heaven....I mean hell.

Engine is coming out, timing cover off and further inspection to make sure nothing else has been damaged.

Leaning towards Sunny's and Steady's pov that E series are bin.

Post by **EFFalcon** » May 7th, 2009, 2:14 pm

AU's are bin... it was an AU engine afterall

Steady · Post by **Steady** » May 7th, 2009, 2:35 pm

t1MMy wrote:*UPDATE*

There is no good news I'm afraid. It was the aux shaft, all the teeth on the gear were just about all stripped off which in turn fvkd the other gears causing some damage.

Put another aux shaft in to see what that go is and it made oil pressure but was making a hell of a noise becasue it fooked the other gears. So oil pump is fine but sounds like all the gears that run off it are in heaven....I mean hell.

Engine is coming out, timing cover off and further inspection to make sure nothing else has been damaged.

Leaning towards Sunny's and Steady's pov that E series are bin.

Sucks that I was right in this case

Theres been a few blokes FM that have done aux gears in AU motors, very weird.
I think one bloke even did 2 in a row LOL

Pfft, I've never actually said that and meant it LOL
Weigh it up, if you still want it, keep it, it's gonna end up cheaper to get a new motor then to get a decent B-Series (read: BF XR6T with ZF trans

)

t1MMy · Post by **t1MMy** » May 7th, 2009, 2:43 pm

I don't need a new motor...yet, hopefuly. If I can just fix what's broken then I'll be happy again.

Steady · Post by **Steady** » May 7th, 2009, 2:47 pm

If valves didn't hit pistons you were lucky!

t1MMy · Post by **t1MMy** » May 7th, 2009, 2:48 pm

Dont fkn say that!

Post by **EFFalcon** » May 7th, 2009, 2:59 pm

if it ran the valves should be fine.

fastea · Post by **fastea** » May 7th, 2009, 3:01 pm

Steady wrote:
t1MMy wrote:*UPDATE*

There is no good news I'm afraid. It was the aux shaft, all the teeth on the gear were just about all stripped off which in turn fvkd the other gears causing some damage.

Put another aux shaft in to see what that go is and it made oil pressure but was making a hell of a noise becasue it fooked the other gears. So oil pump is fine but sounds like all the gears that run off it are in heaven....I mean hell.

Engine is coming out, timing cover off and further inspection to make sure nothing else has been damaged.

Leaning towards Sunny's and Steady's pov that E series are bin.
Sucks that I was right in this case
Theres been a few blokes FM that have done aux gears in AU motors, very weird.
I think one bloke even did 2 in a row LOL

Pfft, I've never actually said that and meant it LOL
Weigh it up, if you still want it, keep it, it's gonna end up cheaper to get a new motor then to get a decent B-Series (read: BF XR6T with ZF trans )

Do they do it because you shove that thingy in there that the EFs have? where the dizzy is ment to go. Dont in AU's just have a cap covering it? Or do I have nfi what Im on about?

Mr. CVE · Post by **Mr. CVE** » May 7th, 2009, 3:06 pm

fastea wrote:
Steady wrote:
t1MMy wrote:*UPDATE*

There is no good news I'm afraid. It was the aux shaft, all the teeth on the gear were just about all stripped off which in turn fvkd the other gears causing some damage.

Put another aux shaft in to see what that go is and it made oil pressure but was making a hell of a noise becasue it fooked the other gears. So oil pump is fine but sounds like all the gears that run off it are in heaven....I mean hell.

Engine is coming out, timing cover off and further inspection to make sure nothing else has been damaged.

Leaning towards Sunny's and Steady's pov that E series are bin.
Sucks that I was right in this case
Theres been a few blokes FM that have done aux gears in AU motors, very weird.
I think one bloke even did 2 in a row LOL

Pfft, I've never actually said that and meant it LOL
Weigh it up, if you still want it, keep it, it's gonna end up cheaper to get a new motor then to get a decent B-Series (read: BF XR6T with ZF trans )
Do they do it because you shove that thingy in there that the EFs have? where the dizzy is ment to go. Dont in AU's just have a cap covering it? Or do I have nfi what Im on about?

yes au's have a cap however it still has the dizzy gear and driveshaft for the oil pump.

Phillis · Post by **Phillis** » May 7th, 2009, 5:22 pm

NOW try and convince me to manual mine

t1MMy · Post by **t1MMy** » May 7th, 2009, 5:42 pm

Being a 5 speed has nothing to do with it.

EBOOST · Post by **EBOOST** » May 7th, 2009, 6:07 pm

yeah au motors with dizzy's seem to do this farely regularly discnt had 2 or 3 in a row do it.
is it that they make the shaft thinner or weaker as they only has the sensor to turn not a dizzy?
cheers josh.

Mr. CVE · Post by **Mr. CVE** » May 7th, 2009, 6:12 pm

the shaft only ever turned the oil pump.
dizzy never had any load, the only ever load will be the oil pump, I have seen this happen when you run HV oil pumps and or thicker oil.
But it may be more something got sucked up the oil pump and locked it up and has rattled out, I have seen this many times.

t1MMy · Post by **t1MMy** » May 7th, 2009, 7:51 pm

Yeah who knows. I'll get a picture of the shaft when I get the car back home so you can see it. Sounds like it did a decent job of sheering the teeth off it though. Lucky the car has a oil pressure gauge on it or I wouldn't have known wtf was going on!!!

Post by **EFFalcon** » May 7th, 2009, 7:58 pm

oil light would have given a hint

t1MMy · Post by **t1MMy** » May 7th, 2009, 8:20 pm

lol it did that anyway

iceman · Post by **iceman** » May 8th, 2009, 12:12 pm

i have to experianced this problem running au engine with dizzy!!, i was warned but also advised this was ok to do

however only 5,000klms when i removed the engine i found the gears also starting to stip off the dizzy wtf

au engine and dizzys are not my suggestion

Steady · Post by **Steady** » May 8th, 2009, 12:29 pm

Is the AU gear a different profile or something?
Maybe AU motor + E-Series aux gear is the way to go?

ClassicAU · Post by **ClassicAU** » May 8th, 2009, 12:31 pm

Or AU motor + rest of AU = WIN!

Post by **EFFalcon** » May 8th, 2009, 12:51 pm

But TIm's car is an EF.
No dizzy!

t1MMy · Post by **t1MMy** » May 8th, 2009, 12:55 pm

iceman wrote:i have to experianced this problem running au engine with dizzy!!, i was warned but also advised this was ok to do

however only 5,000klms when i removed the engine i found the gears also starting to stip off the dizzy wtf

au engine and dizzys are not my suggestion

My engine is running off a coil pack.
It still has a shaft that goes into the motor where the dizzy would normally sit, but it just has a plate with a sensor on the end of it.
I never heard of this being a problem until it happened to my car but apparently it is pretty common.