Wanted: Introduction

by **Adypie** » March 1st, 2010, 3:03 pm

Hi, my name is Adam and I'm a "falcoholic". Yes that was pretty corny.
I've recently bought an ED XR6. Need a bit of work and guidance to get it back to top notch. The journey begins.
So yeah, how's it goin?

by **EFFalcon** » March 1st, 2010, 3:11 pm

welcome, got any plans for it?

by **SnyperEB** » March 1st, 2010, 3:13 pm

Pics?

by **Adypie** » March 1st, 2010, 3:31 pm

I'll get some pics up tonight hopefully. My plans are limited due to laws on provisional drivers and turbos/kWs.

by **Dumpsta** » March 1st, 2010, 4:08 pm

Welcome mate. :drinks2:

Not an introduction thread without pictures...

by **Phillis** » March 1st, 2010, 7:16 pm

welcome. theres quick alot you can do to a car while keeping it naturally aspirated. where abouts are you located?

by **Mr_EF_96** » March 1st, 2010, 7:53 pm

Welcome mate.

If your restricted by p plate laws mate the best answer would be a 2 1/2 cat back system and a chip and cold air intake and filter.
You can advance the timing and also install a aftermarket chip like the J3.

In vic im sure your not allowed to have extractors and highflow cats until your off your red p plates but im not sure where your from so that might not affect you.

Put some pics up and you will get alot more info about what you can mod.

Good luck with your build.

by **Adypie** » March 1st, 2010, 7:59 pm

Sorry about the wait, and I forgot the assend. I got it with the 2.5inch exhaust, not sure on the details of it though :S
Planning on extractors

by **Adypie** » March 1st, 2010, 7:59 pm

Cheers to everyone for the welcomes

by **Joshe94** » March 1st, 2010, 8:33 pm

Welcome, I'm new to E-series too :lol:

Nice car man, how much did it cost if you don't mind me asking.
I've got a '93 ED XR6 in Polynesian green! :grin:

by **Adypie** » March 1st, 2010, 8:43 pm

Mines a '94, same car! About $1500 as is. It's had engine work and miscellaneous costs since then of course!

by **Joshe94** » March 1st, 2010, 8:46 pm

Nice, I payed $1900 as is for mine.
I've got a build thread here if your keen on reading it

viewtopic.php?f=3&t=13993&start=0

by **Adypie** » March 1st, 2010, 9:40 pm

Where did you find those rims??!! Mine are corroded / unnatural!
Your paint is much better than mine is too. Need a respray pretty badly. Already done the bonnet in the pics.
Planning on black plush carpet for mine, have a nice design thought out. Helps being a painter and decorator

by **Adypie** » March 1st, 2010, 9:49 pm

You still got your old wheels josh? If so, how much?

by **Joshe94** » March 2nd, 2010, 3:48 pm

My dad found the rims at a swap meet, I couldn't believe it.
The clear paint is peeling a fair bit on them, but I can always re-clear them in the future.
Black plush sounds good!

And about the wheels, I've still got them. But I'm in Victoria.

by **Joshe94** » March 4th, 2010, 2:44 pm

Hey, if your keen on the wheels, you can have them for $500.

Wanted: Introduction

Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Re: Wanted: Introduction

Who is online