Au xr6 head on normal EF 4.0I OHC

This is a general discussion forum, open to all participants

Au xr6 head on normal EF 4.0I OHC

Postby Sunshinecoast » March 29th, 2010, 9:11 pm

is it achievable or better just staying with the normal ef,,,,,head..?
Sunshinecoast
Idling
 
Posts: 12
Joined: March 28th, 2010, 1:19 am
Has Liked: 0 time
Been Liked: 0 time

1995 Ford Falcon

Re: Au xr6 head on normal EF 4.0I OHC

Postby needfordspeed » March 29th, 2010, 9:16 pm

Is it VCT or not? If not it will go on no worries, just make sure you use the AU cam and rocker gear too. What are you trying to do with the car? If it's a stocker then don't bother going with the AU head.
1988 EA S-Pack - 10.6@125MPH New build underway
User avatar
needfordspeed
Moderator
Moderator
 
Posts: 5256
Joined: July 13th, 2007, 2:13 pm
Has Liked: 110 times
Been Liked: 417 times

1988 Ford S Pack

Re: Au xr6 head on normal EF 4.0I OHC

Postby Sunshinecoast » March 29th, 2010, 9:25 pm

cheers ,, just extractors pacemakers and 2.5exuast so im prob better off staying with the reconditioned ef/el head?
Sunshinecoast
Idling
 
Posts: 12
Joined: March 28th, 2010, 1:19 am
Has Liked: 0 time
Been Liked: 0 time

1995 Ford Falcon

Re: Au xr6 head on normal EF 4.0I OHC

Postby needfordspeed » March 29th, 2010, 9:31 pm

If it was me i'd probably go the AU head if it's not too dear.
1988 EA S-Pack - 10.6@125MPH New build underway
User avatar
needfordspeed
Moderator
Moderator
 
Posts: 5256
Joined: July 13th, 2007, 2:13 pm
Has Liked: 110 times
Been Liked: 417 times

1988 Ford S Pack

Re: Au xr6 head on normal EF 4.0I OHC

Postby Sunshinecoast » March 29th, 2010, 10:44 pm

so will the cover from my old head go straight on to the tickford xr6 head?
Sunshinecoast
Idling
 
Posts: 12
Joined: March 28th, 2010, 1:19 am
Has Liked: 0 time
Been Liked: 0 time

1995 Ford Falcon

Re: Au xr6 head on normal EF 4.0I OHC

Postby misk » March 29th, 2010, 10:56 pm

sure will mate
XG Panelvan
EF bottom end with ported EB head, valve springs, EL ECU & J3 chip, crane HI6 CDI & MSD coil, LC-1 wideband & SSI-4 logger

soon - .595" lift cam, GT4202, forged AU engine and built head, ems stinger 4424 ecu, powerglide with 5500 high stall etc - next, bellhousing

XH ute daily - DOHC BA XR6 engine, T5, AU3 ECU with TI J3 chip, ported BBM, 3" stainless intake - 12" sub, tub liner and hard lid - mass skids and epic tyre carrying capabilities :)
User avatar
misk
Melting Pistons
 
Posts: 10047
Joined: October 14th, 2008, 10:31 am
Location: dandenong
Has Liked: 298 times
Been Liked: 295 times


Return to General Discussion

Who is online

Users browsing this forum: No registered users