Hi guys,
I need some advise on my old kenwood deck that i connected to my el falcon. Everything seems ok but i cannot get sound through the speakers. Illumination is fine, cd ejects, all speaker wiring is connected to the factory wiring but no sound!!
The funny thing is if i connect a amplifier to the kenwood deck than i get sound but if that is disconnected than no sound!!
pls help!!
cheers
No sound :(:(:(
7 posts
• Page 1 of 1
No sound :(:(:(
by SIXSEATER » April 24th, 2010, 7:07 pm
-
SIXSEATER - Idling
- Posts: 195
- Joined: September 16th, 2009, 6:26 pm
- Has Liked: 0 time
- Been Liked: 0 time
Re: No sound :(:(:(
by SIXSEATER » April 24th, 2010, 8:04 pm
is there anyway i can switch it on or off or is that all automatic?
-
SIXSEATER - Idling
- Posts: 195
- Joined: September 16th, 2009, 6:26 pm
- Has Liked: 0 time
- Been Liked: 0 time
Re: No sound :(:(:(
by josh_ef » April 24th, 2010, 9:01 pm
kenwood decks are pretty ordinary in general
so when you connect an amp to run speakers through rca's it plays sound?
i would agree that the head units internal amp is gone.
just keep running an amp or look at a new deck, pioneer or alpine is a good start
so when you connect an amp to run speakers through rca's it plays sound?
i would agree that the head units internal amp is gone.
just keep running an amp or look at a new deck, pioneer or alpine is a good start
- josh_ef
- Breaking Traction
- Posts: 1985
- Joined: January 15th, 2010, 1:41 am
- Has Liked: 50 times
- Been Liked: 20 times
Re: No sound :(:(:(
by misk » April 24th, 2010, 9:12 pm
id pull it out and just retest that you have the wires correct.
if you do, then as said above, no good!
if you do, then as said above, no good!
XG Panelvan
EF bottom end with ported EB head, valve springs, EL ECU & J3 chip, crane HI6 CDI & MSD coil, LC-1 wideband & SSI-4 logger
soon - .595" lift cam, GT4202, forged AU engine and built head, ems stinger 4424 ecu, powerglide with 5500 high stall etc - next, bellhousing
XH ute daily - DOHC BA XR6 engine, T5, AU3 ECU with TI J3 chip, ported BBM, 3" stainless intake - 12" sub, tub liner and hard lid - mass skids and epic tyre carrying capabilities
EF bottom end with ported EB head, valve springs, EL ECU & J3 chip, crane HI6 CDI & MSD coil, LC-1 wideband & SSI-4 logger
soon - .595" lift cam, GT4202, forged AU engine and built head, ems stinger 4424 ecu, powerglide with 5500 high stall etc - next, bellhousing
XH ute daily - DOHC BA XR6 engine, T5, AU3 ECU with TI J3 chip, ported BBM, 3" stainless intake - 12" sub, tub liner and hard lid - mass skids and epic tyre carrying capabilities
-
misk - Melting Pistons
- Posts: 10047
- Joined: October 14th, 2008, 10:31 am
- Location: dandenong
- Has Liked: 298 times
- Been Liked: 295 times
Re: No sound :(:(:(
by SIXSEATER » April 24th, 2010, 10:25 pm
thx for the replies guys, i re-confirmed the wiring and all of that is fine and still have the same issue.
It works well when connected to an amp but yeh no sound on its own.... It seems the internal amp is gornnee...
It works well when connected to an amp but yeh no sound on its own.... It seems the internal amp is gornnee...
-
SIXSEATER - Idling
- Posts: 195
- Joined: September 16th, 2009, 6:26 pm
- Has Liked: 0 time
- Been Liked: 0 time
Re: No sound :(:(:(
by S1KHXR » April 24th, 2010, 11:09 pm
yeah the head units given up lol
that happend to one that i had in the fairline when i took the amps out to put in the XR.
put a new deck in and it worket fine
that happend to one that i had in the fairline when i took the amps out to put in the XR.
put a new deck in and it worket fine
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users