JETEL6's "Chook" Officially T56'd + Happy Snaps!

WILLEBII · Post by **WILLEBII** » January 15th, 2012, 9:59 pm

did you get this 6 speed installed?

JETEL6 · Post by **JETEL6** » January 24th, 2012, 10:10 pm

hey all,

bout time for an update!

been a while, i now have all the bits for the the T56 Conversion, including the E-Series Hydraulic Pedal Kit (thanks HEAPS to Paul @ Mal Wood) as well as new injectors, new clutch and new suspension bits! (thanks Justin @ Tuff Car Parts)

i have been working on it a bunch as i hope to have it ready to see Paul @ CVE very soon for a full house tune!

i really hoped to have it finished by Geelong AFD, though by now i really have my doubts due to work commitments and uni starting soon, which generally means lack of proper time to work on her

ah well!

also, i fitted the 1.0mm oil restrictor for the turbo oil feed today so ill chuck up a pic of the differences haha!

Kind Regards,
Daniel

JETEL6 · Post by **JETEL6** » January 24th, 2012, 10:16 pm

WILLEBII - Nope not as yet, i have all the parts, just need to reassemble the gearbox!
The car is on my hoist ready to go, just need the time haha!
is there anything you needed to know?

Regards,
Daniel

JETEL6 · Post by **JETEL6** » January 28th, 2012, 8:46 pm

installed my new clutch today!

plus i trial fitted my T56 Bellhousing! Cant Wait!!

Kind Regards,
Daniel

misk · Post by **misk** » January 28th, 2012, 8:53 pm

Bet the restrictor will make a difference lol! Good work.

JETEL6 · Post by **JETEL6** » January 28th, 2012, 8:58 pm

haha yeah, no suprise that she was a smoker!

JETEL6 · Post by **JETEL6** » February 8th, 2012, 9:08 pm

keeping at it where i can get time!

clutch fluid reservoir is all mounted up (plus it made for a radical place to fit my boost controller!)

New input shaft trail fitted (diggin' those massive gears

)

Regards,
Daniel

EBOOST · Post by **EBOOST** » February 8th, 2012, 9:12 pm

ive got a few questions.

why did u decide to change the input shaft when u need a clutch anyway?

i only ask that as u said in rat's thread u are getting an off the shelf xtreme.
why not get a clutch a flywheel package in 11" and never have to worry about it?

people put soft clutches in t5's to try save them u dont need to do that with a t56 so id be spending a bit extra so i wouldnt have to worry about it thats all.

JETEL6 · Post by **JETEL6** » February 8th, 2012, 9:20 pm

i had to change the input shaft to suit the Bellhousing as the VY input shaft was to long, and the input shaft available was a 10 spline to suit standard clutches.

The reason i went with this clutch was for budget reasons, as i couldnt afford anything better at the time and this will suit my current power levels just fine.

if/when i up the boost further i will just change to a cushion button disc as the XHD pressure plate has an 1100kg clamp.

EBOOST · Post by **EBOOST** » February 8th, 2012, 9:22 pm

fair enough man.

the hd pressure plate i thought was 1100kg and the xhd was 1300kg?

cushion button is only a couple of hundred more.
i cant talk im on a massive budget haha.

let us know how it goes.
cheers josh.

JETEL6 · Post by **JETEL6** » February 8th, 2012, 9:27 pm

yeah the XHD may be 1300kg, i'm sure ill find out haha!

I have already purchased and fitted the new clutch, but i have a friend who works at an exedy dealer so i can get pretty cheap discs, though i really wanted the Xtreme pressure plate so i just bought their kit.

i'll keep the updates coming!

Regards,
Daniel

JETEL6 · Post by **JETEL6** » April 16th, 2012, 9:10 pm

been a while!

as with all projects, i hit a few month slump though i'm now back into it full force!

T56 conversion is 98% complete, just need to bleed the clutch and set the speedo corrector

Fitted a new 32mm Copper Radiator, as the old one split the tanks!

plan is too drive it for a few hundred k's to bed the clutch in, then its off to CVE for a 12-14psi tune.

Happy to answer any questions.

Regards,
Daniel

NUT347 · Post by **NUT347** » April 18th, 2012, 9:50 pm

You will love driving it with a 6 speed.. Nothing like smashing 3rd without the fear of leaving it behind..

Bump for more pics!

JETEL6 · Post by **JETEL6** » April 20th, 2012, 10:57 pm

NUT347 wrote:You will love driving it with a 6 speed.. Nothing like smashing 3rd without the fear of leaving it behind..

just drove it now!

what a difference it has made to the whole driving experience (1-4th gear ratios are magic) the hydraulic clutch is worth its weight in gold haha

that certain third gear-itis as been lifted from my shoulders haha!

Regards,
Daniel

JETEL6 · Post by **JETEL6** » April 20th, 2012, 11:53 pm

in regards to pics

i only have one new one, i cut out my single din fascia to accept a trio of gauges

p.s forgive the mess and the gaps haha!

Regards,
Daniel

justa6 · Post by **justa6** » April 21st, 2012, 6:16 am

well done. i would of liked to have seen the reservoir and bleed valve a bit further away from the hot stuff.

Rollin · Post by **Rollin** » April 21st, 2012, 10:21 am

Yeah as per justa6 - heat is bad mmkay? At least put a layer of heat shielding around the reservior and another over the turbo and dump to try and keep it cool.

Is 1mm enough for the restrictor? I thought the usual was about 3? You don't want to starve the turbo of oil...

You do forget how many thousands it cost to get the 6 speed in there once you drive it for the first time hey - it's fucking magic being able to smash gears and not need the number of your friendly neighbourhood towie on speed dial!

JETEL6 · Post by **JETEL6** » April 21st, 2012, 7:13 pm

heat leads to all kinds of nasties, this i know haha!

the dump pipe is double wrapped in heat wrap, and the turbo has a big F-Off beanie on it.

though making a heat shield for the reservoir isn't a bad idea, thanks Rollin!

Regards,
Daniel

OED666 · Post by **OED666** » April 23rd, 2012, 12:40 pm

hey, just looking at your test fit up of the clutch and bellhousing, and i noticed that you dont have a sandwich plate between the block and bellhousing... have you fitted one since? This will effect your CSC height setup...

JETEL6 · Post by **JETEL6** » April 23rd, 2012, 1:04 pm

I machined 8mm from the CSC mount on the gearbox faceplate.

I have since driven it and the pressure plate doesn't seem to bottom out.

You would know if it's wrong though of course haha!

Regards,
Daniel

OED666 · Post by **OED666** » April 23rd, 2012, 8:26 pm

Did you check the CSC crush before you installed the box?

JETEL6 · Post by **JETEL6** » April 23rd, 2012, 8:54 pm

yeah i measured it to make sure, did i make a mistake?

it now has the original sandwich plate between the bellhousing and block, at the time of the trial fit it want present.

OED666 · Post by **OED666** » April 23rd, 2012, 9:29 pm

Ok, as long it was between 14 to 17mm..

JETEL6 · Post by **JETEL6** » April 23rd, 2012, 9:43 pm

im assuming i would know if it was wrong haha, all seems well though!

Thanks for your concern Paul

JETEL6 · Post by **JETEL6** » May 1st, 2012, 4:58 pm

went for a drive today and took a few happy snaps!

not the cleanest its ever been but you get the idea.

and also, i took a picture of the No.1 & No.2 Spark plug to determine how my current tune is holding up (they are ~200km's old).

What do y'all reckon?
No.1

No.2

Enjoy!

Regards,
Daniel

SnipeZ · Post by **SnipeZ** » May 1st, 2012, 7:32 pm

What advantages.can be had running the ea overflow opposed to the eb+

JETEL6 · Post by **JETEL6** » May 1st, 2012, 8:03 pm

I don't think there are any, it just happened to suit my hot side IC piping haha!

sikwags_218 · Post by **sikwags_218** » May 1st, 2012, 8:23 pm

More space snipez, is the short answer. You can get your hot side piping and the front dose pipe in. Cause you can get rid of the battery tray and the coolant reservoir holding bracket

SnipeZ · Post by **SnipeZ** » May 1st, 2012, 8:26 pm

Ah thanks for that

Just seen heaps with that bottle

sikwags_218 · Post by **sikwags_218** » May 1st, 2012, 8:28 pm

Yeah no worries mate

Yeah i'm running that bottle in mine to. Just needs me to finish the motor

JETEL6 · Post by **JETEL6** » May 1st, 2012, 8:39 pm

sikwags_218 wrote:More space snipez, is the short answer. You can get your hot side piping and the front dose pipe in. Cause you can get rid of the battery tray and the coolant reservoir holding bracket

couldn't have worded it better myself!

JETEL6 · Post by **JETEL6** » May 5th, 2012, 11:21 pm

Update!

i did a compression check on the motor and it has been revealed that my No.6 cylinder has bitten the dust

on the plus side, I'm thinking of putting an AU motor in it now with F6 Conrod/Piston Package!
are these parts readily available from fraud? or would i be better off to buy decent rods and aftermarket pistons?

also, will there be any nasty ramifications if i use me EL head?

Kind Regards,
Daniel

Boosted Falcon

JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook" Almost Six Speed Time!

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook"

Re: JETEL6's "Chook"

Re: JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd

JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd

JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!

Re: JETEL6's "Chook" Officially T56'd + Happy Snaps!